75 - 25 Ton Vertical Wall-Mount HVAC Units

Unit Accessories

  • SPSA Series Spiral Pipe Stack Assemblies
  • Flexible Intake Ducts
  • Wall-Mount Convection Heaters
  • Gas Detection Systems
  • Remote Alarm Beacons & Horns
  • RECO Series Remote Emergency Control Operators
  • Explosion-Proof Disconnects
  • Condenser Air Filters
  • Return Air Filters

A wide range of accessories enhance our Through-Wall and Window Mount Air Conditioners & Heat Pumps to meet your precise application requirements!

Scroll down or contact a Bebco Sales Associate to learn more…

MORE INFORMATION

Click any item to enlarge…

SPSA Series Spiral & RPSA Series Rigid Pipe Stack Assemblies

Bebco provides these assemblies to serve as a fresh air intakes for our Wall Mount Air Conditioners and Heat Pumps. Spiral Pipe Stacks are an essential accessory that provide an economical and guy-wire secured source of fresh air.

When properly secured, these stacks are designed to withstand extremely high wind-loads, are certified for coastal areas, and they are provided with a very wide range of accessories including fittings, flexible duct connectors, anchor kits and rain caps.

Bebco provides all necessary accessories to complete your installation easily!

SPSA Series

Model SP Spiral Pipe Stacks, along with Model SN Ninety and Model ST Tee Stack Fittings and Model SC Stack Caps provide an economical and easily installed fresh air intake system for Bebco Wall Mount Air Conditioners & Heat Pumps. The Model SP Spiral Pipe Stacks are available in standard lengths of 10 or 14 feet and in custom lengths, with 12”, 16”, 20”, and 24” diameters in either galvanized or stainless steel materials with optional finishes. Model CAGK and EAGK Concrete Anchor and Earth Auger Kits provide complete guy wire support systems, including ground level anchors, spiral pipe guy wire attachment brackets, turnbuckles and guy wire cable.

As an alternative, Bebco also offers a unique telescoping Model SPSK Spiral Pipe Stanchion Kit to eliminate some or all guy wire supports. Finally, to facilitate easy connection to a Bebco Wall Mount Air Conditioner or Heat Pump Unit, and eliminate alignment and stress issues, Bebco recommends the use of Model FDC Flexible Duct Connectors.

SPSA Series

Spiral Pipe Stack Assemblies
Provides an economical fresh air intake system for
Bebco Wall Mount Air Conditioners and Heat Pumps.

SP, SC, ST & SNSpiral Pipe, Caps, Tees & Nineties
* Materials: *16 or 20 Gauge Bodies & 1/4" or 3/16"
Flanges in Galvanized, 304 Stainless
Steel or 316 Stainless Steel Material
*Finishes: * Unfinished, Hot Dipped, or
Urethane Painted
*Stack Diameters: * 8", 10", 12”, 16”, 18", 20” or 24”
Accessories
*Model BC *Blind Covers
*Model FDC * Flexible Duct Connectors
*Model GBK * Gasket & Bolt Kits
*Model SPAK * Spiral Pipe Anchor Kits
*Model CAGK * Concrete Anchor Guy Wire Kit
*Model EAGK * Earth Auger Guy Wire Kit
*Model SPSK * Spiral Pipe Stanchion Kit

Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!

RPSA Series

Model RP Rigid Pipe Stacks, Model RPAK Rigid Pipe Anchor Bolt Kits, and Model SC Stack Caps provide a fresh air intake system for Bebco Wall Mount Air Conditioners and Heat Pumps. The Model RP Rigid Pipe Stacks are available in 12”, 16”, 20”, and 24” diameters in either carbon steel or stainless steel. Model RP Rigid Pipe Stacks are 25 feet tall single piece stacks constructed from seal-welded 1/4” thick (schedule 20) carbon or stainless steel pipe.

The Model RP feature a seal-welded flange at the top for the stack cap connection and a seal-welded blind flange at the bottom for mounting to a concrete slab. To facilitate easy connection to Bebco Wall Mount Air Conditioners or Heat Pumps, and eliminate alignment and stress issues, Bebco recommends the use of Model FDC Flexible Duct Connectors.

RPSA Series

Rigid Pipe Stack Assemblies
Provides a free standing fresh air intake system for
Bebco Wall Mount Air Conditioners and Heat Pumps.

Model RP Rigid Pipe Stack
* Materials: Schedule 20 150# Rated Carbon Steel,
304 Stainless Steel or 316 Stainless Steel
* Finishes: Carbon Steel: Hot Dip Galvanized
Stainless Steel: 2B or Urethane Painted
* Diameters: 8", 10", 12”, 16”, 18", 20” or 24”
Model SC Stack Caps
*Materials: 16 or 20 Gauge Bodies & 1/4" or 3/16"
Flanges in Galvanized, 304 Stainless
Steel or 316 Stainless Steel Material
* Finishes: Carbon Steel: Hot Dip Galvanized
Stainless Steel: 2B or Urethane Painted
Model FDC Flex Duct Connectors
* Duct Material: Polyester/Neoprene w/ Galvanized Helix
*Flange Material: 16 Gauge Galvanized Steel,
304 Stainless Steel or 316 Stainless Steel
Model RPAK Rigid Pipe Anchor Kits
*Materials: Zinc Chromate Plated Carbon Steel.
304 Stainless Steel or 316 Stainless Steel
* Styles: Concrete Epoxy or Wedge Anchors
or Platform Deck B

Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!

Flexible Intake Ducts

The Model FID Flexible Intake Duct provides a temporary, pliable fresh air duct connection to Bebco Model WAC and WHP Units. Model FID is typically utilized in applications where the use of a permanent spiral or rigid pipe stack is not feasible.

When placed properly, the intake housing draws unclassified, fresh air into a Bebco Wall Mount Air Conditioner or
Heat Pump Unit from an unclassified area adjacent to the immediate vicinity.

Bebco provides all necessary accessories to complete your installation easily!

Model FID

Bebco Model FID Flexible Intake Duct housings are manufactured from 304 and 316 stainless steel components, and the duct features a pliable neoprene coated polyester hose with a mechanically embedded galvanized steel helix to withstand years of exposure to harsh operating conditions and corrosive environments.

They serve to provide a source of fresh air where the use of a permanent spiral or rigid pipe stack is not feasible, and they are provided with 25 feet or custom length duct.

Model FID

Flexible Intake Ducts
Provides a temporary, pliable fresh air duct connection to
Bebco Wall Mount Air Conditioner and Heat Pump Units.

*Housing Material: 14 Gauge 304 Stainless Steel
*Housing Finish:Unfinished, Urethane Paint or Custom Finish
*Housing Handle:316 Stainless Steel
*Housing Screen: .047” Wire Diameter x 0.25” Opening
Woven 316 Stainless Steel Mesh
*Duct Material:Neoprene Coated Polyester Fabric
w/ Embedded Galvanized Helix
*Duct Clamps:304 Stainless Steel
*Duct Diameters: 12”, 16”, 20”, or 24”
*Duct Lengths: 25 Feet or Custom Length *

Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!

Wall-Mount Convection Heaters

Bebco provides these accessories to complement our Wall Mount Air Conditioners and Heat Pumps, to provide a
5,500 to 30,700 BTU axillary heat source in your room or building.

These heaters are offered in a variety of voltage, wattage and T-code ratings, can be placed under a Model WAC or WHP Unit, so their heated air can be circulated by the units, and are UL & CSA Listed for Class I, Division 2, Group B, C & D Areas!

Bebco provides all necessary accessories to complete your installation easily!

Model WMCH

Bebco Wall Mount Convection Heaters complement Bebco Wall Mount Air Conditioner and Heat Pump Units by providing an auxiliary source that provides ample heating energy to overcome extremely cold climate conditions. As illustrated in this image, the effect of these Wall Mount Convection Heaters is amplified by placing them under our Air Conditioner or Heat Pump Unit’s Supply and Return Grilles.

The Air Conditioner or Heat Pump Unit can then be operated in fan only or heating mode to recirculate and distribute the convection heated air efficiently throughout your building or room!

Model WMCH

Wall Mount Convection Heaters
Provides 5,500 BTU 1.6 kW to 30,700 BTU 9.0 kW Heating Force!

These units feature integrated contractors and may feature integrated or remote temperature controllers, sold separately. Please contact a Bebco Sales Associate or review our Technical Bulletin for more information.

Specify and install one or more Units
to attain required heating capacity!

*T3A Rated Heaters: 5,500 (1.6 kW) BTU, 11,000 (3.2 kW) BTU
& 13,600 (4.0 kW) BTU
* T2A Rated Heaters 6,156 (1.8 kW) BTU, 12,900 (3.6 kW) BTU,
24,000 (7.6 kW) BTU & 30,700 (9.0 kW) BTU
*Power Ratings: 208, 240 or 480 VAC, 1 or 3 Ph, 50/60 Hz
*Common Overall Depth: 9 Inches
*Common Overall Height: 20 Inches
* 1.6, 1.8 & 3.6 kW Widths: 34 Inches*
* 3.2 & 7.6 kW Widths:58 Inches*
*4.0, 4.5 & 9.0 kW Widths: 70 Inches*
* Dimensions exclude Conduit Fittings
*Certifications: UL & CSA Listed for US & Canada
*Special Options: 304 or 316 Grade Stainless Steel Housings
High Temperature Heresite® Coil Coatings

 

Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!

Gas Detection Systems

Bebco provides these accessories to achieve the ultimate level of safety when Model WAC and WHP Units are fitted on buildings containing analyzers or other processing equipment that requires hydrocarbon gas, H2S gas or O2 deficiency monitoring.

These systems can be integrated easily and come with all necessary components to detect critical hazards and warn
your facility’s safety personnel of potentially catastrophic conditions.

Bebco provides all necessary accessories to complete your installation easily!

Model CGDM, HGDM, OGDM & GDPS

Bebco Model GSA Gas Detection Systems are intended to alert your team to unacceptable levels of flammable, combustible or toxic gases, or to monitor oxygen levels within a building containing analyzers or other chemical processing equipment.

The power supply requires a 120 VAC power source and feeds 24 VDC to the monitor, which powers the sensor within the protected enclosure. The monitor then sends a 4-20 ma signal to an alarm monitoring system to alert your staff of critical conditions.

When it comes to ensuring your team’s safety, Bebco has a total solution and the expertise to help you get it properly installed!

Model CGDM, HGDM, OGDM & GDPS

Monitors, Matching Sensors & Power Supplies
Provides detection of hydrocarbons, H2S or O2 deficiency!

* Hydrocarbon Monitor: Catalytic Bead Adsorption - 0-100% LEL
Accuracy & Repeatability: +/- 5% Full Scale
Zero Drift: < 5% per Year
*H2S Monitor: Metal Oxide Adsorption - 0-100 PPM
Accuracy & Repeatability: +/- 5% Full Scale
Zero Drift: < 2% per Year
* O2 Monitor: Electrochemical Fuel Cell - 0-26%
Accuracy & Repeatability: +/- 2% Full Scale
Zero Drift: < 2% per Month
*Response/ Op Temp: 90% < 30 Seconds / -40° to 175° F
* Housing Ratings: NEMA 7, Class 1, Division 1, Group C & D
* Housing Dimensions: 5.5" H x 5.3" W x 4.0" D (GDPS is 6.0" D)
*Sensor Dimensions: 3.0" H x 2.0" Diameter
*Power Requirements: Monitor: 22-28 VDC / Power Supply: 120 VAC
* Signal Output: 4-20ma VDC, Linear
*Alarm Contacts: Low & High Set Points & Fault Supervision
Form C 0.5 amps @ 125 VAC or 30 VDC
Programmed to open or close on alarm
*Conduit Ports: 3/4" Top & Bottom Sides
*Certification: UL Listed

Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!

Remote Alarm Beacons & Horns

Bebco provides these accessories to act as a local alarm to indicate Model WAC Air Conditioner and Model WHP Heat Pump Unit faults and building temperatures above or below the alarm set points you can set with the Unit Controls.

These alarm devices can be mounted outdoors, are rated for the Hazardous Location and are perfect companions to our Wall Mount Units, when the Unit’s alarm contact is used to drives remote alarms.

Bebco provides all necessary accessories to complete your installation easily!

Model ERAB, RAB & RAH

Available for Class I, Division 1 or Class I, Division 2 applications, Bebco Model RAB-1, RAB-2 and ERAB-2 Remote Alarm Beacons and Model RAH-1 and RAH-2 Remote Alarm Horns are intended to provide audible or visual signals that summon Operators to resolve loss of building or room pressure, when used in conjunction with Bebco Hazardous Location Wall Mount Air Conditioner and Heat Pump Remote Alarm Contacts.

These alarm devices can also be used in conjunction with our Gas Detection Systems to address the presence of combustible or corrosive gases or investigate oxygen deficiencies, or with both sets of contacts for a common trouble alarm, if wired in series. All devices are listed for use in Class I, Division 1 or Division 2 Hazardous Locations, and are considered as highly suitable alarm devices by most industry standards.

Model ERAB, RAB & RAH

Remote Flashing Alarm Beacons & Audible Tone Horns
Provide visual and audible signals to summon Operators to fault conditions

ERAB-2Economy Remote Alarm Beacon
* Materials: Aluminum Housing w/ Polyurethane Finish
& Polycarbonate Outer Dome
*Mounting: Pendant w/ 3/4" Conduit
* Dimensions: 7.5” H x 5.5” Diameter
* Shipping Weight: 2 Pounds
*Operating Temp: -40° F - 104° F
*Operating Voltage: 12-24 VDC @ 1.70-0.70 Amps
24 VDC @ 0.70 Amps
120 VAC @ 0.21 Amps
240 VAC @ 0.13 Amps
*Flash Rate: 80 / Minute
* Certifications: Class I, Div 2 - UL Listed, CSA Certified
RAB-2Flashing Remote Alarm Beacon
* Materials: Cast Aluminum Body with Epoxy Finish
& Glass Dome w/ Optional Guard
*Mounting: Pendant or Ceiling w/ 3/4" Conduit
* Dimensions: 9.25” H x 5.5” Diameter
* Shipping Weight: 5 Pounds
* Operating Temp: -31° F - 104° F
* Operating Voltage: 24 VDC @ 0.4 Amps
120-240 VAC @ 0.21-0.13 Amps
277 VAC @ 0.13 Amps
* Flash Rate: 60 / Minute or Steady Burn
* Certifications: Class I, Div 2 - UL Listed, CSA Certified
RAH-2Continuous Tone Remote Alarm Horn
* Material: Die Cast Zinc w/ Polyurethane Finish
* Mounting: Surface w/ 3/4" Conduit
* Dimensions: 4.53” H x 6.02” W x 3.66” D
* Shipping Weight: 3 Pounds
*Operating Temp: -65° F - 150° F
*Maximum Sound: 100 Decibels at 10 ft.
*Operating Voltage: 120VAC 50/60Hz @ 0.18 amps
240VAC 50/60Hz @ 0.09 amps
*Certification: Class I, Div 2 - UL Listed, CSA Certified
RAB-1Div 1 Flashing Remote Alarm Beacon
*Materials: Cast Aluminum Body with Epoxy Finish
& Glass Dome w/ Optional Guard
* Mounting: Pendant, Wall or Ceiling Mount w/ 3/4 Conduit
*Dimensions: 14.26" - 15.48" H x 8.80” Diameter
* Shipping Weight: 15.9 -19.8 Pounds
*Operating Temp: -67° F - 150° F
* Operating Voltage 24 VDC @ 1.9 Amps
120 VAC 50/60 Hz @ 1.14 Amps
240 VAC 50/60 Hz @ 1.14 Amps
* Flash Rate: 80 / minute
*Certifications: Class I, Div 1 - UL Listed, CSA Certified
RAH-1Div 1 Continuous Tone Remote Alarm Horn
* Material: Cast Aluminum Body
*Mounting: Pendant or Surface w/ 3/4" Conduit
* Dimensions: 7.625” H x 6.875” D x 6.5” D
*Shipping Weight: 12 Pounds
*Operating Temp: -13° F - 104° F
* Maximum Sound: 100 Decibels at 10 ft. (5 minute duty cycle)
* Operating Voltage: 24 VDC @ 1.2 Amps
120 VAC 50/60 Hz @ 0.20 Amps
240 VAC 50/60 Hz @ 0.10 Amps
* Certification: Class I, Div 1 - UL Listed, CSA Certified

Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!

RECO Series Remote Emergency Control Operators

Bebco RECO Series Remote Emergency Control Operators are intend to activate or deactivate the emergency shutdown (ESD) and emergency control over-ride (ECO) functions of Bebco Wall Mount Air Conditioners and Heat Pumps.

They are designed to work in conjunction with hard-wired or intrinsically safe inputs to these units, and they can operate independently or in conjunction with other safety devices such as our Model CGDM Combustible Gas Detection Monitor.

Bebco provides these accessories to provide remote control inputs to your pressurization unit!

RECO Series

Bebco RECO Series Remote Emergency Control Operators meet the most demanding needs for strength, along with corrosion, chemical and UV resistance. RECO Series Enclosures are formed as molded polyester housings and covers with a recessed high temperature neoprene gasket and captive stainless steel screws.

The enclosures are watertight, dust tight, double insulated and non-conductive, making them ideal for any location, even when subjected to frequent wash-downs. RECO Series Operators are also incredibly durable, with highly corrosion and chemical resistant bodies and internal metal operator components to provide the perfect combination of durability and strength essential to industrial applications.

RECO Series

Remote Emergency Control Operators
Provides remote control of emergency shutdown
and over-ride functions!

* Housing Material: Fiberglass Reinforced Polyester
* Cover Gasket Material: Memory Retaining Polyurethane
* Enclosure Dimensions: 6-5/8” H x 3-13/16” W x 3-57/64” D
* Conduit Connection: One (1) 3/4" Bottom Side Conduit Knockout
* Certifications: UL & CSA Listed as Type 1, 3, 4X, 6P & 12
* Temperature Range: -40 to +250° F (-40 to +120° C)
* Flammability Rating: UL94-5V, Self-extinguishing, non-flame propagating
* Conductivity Rating: Non-conductive, Double Insulated
* Environmental Rating: UV and Chemical Resistant
*Operator & Contact Blocks:
Thermoplastic Polyester
*Ordinary Block Certifications: UL & CSA Listed for Industrial Use
* Hazardous Block Certifications: UL & CSA Listed for Class I, Division 2,
Groups B, C & D

Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!

Explosion-Proof Disconnects

Bebco provides this accessory to serve as a disconnect for Bebco Wall Mount Air Conditioners and Heat Pumps,
which may be required depending on how the unit is powered.

These disconnects can be mounted on or near the unit, are rated for the Hazardous Location and are a perfect solution for proper power control.

Bebco provides all necessary accessories to complete your installation easily!

Model EDS

Bebco Model EDS Explosion-Proof Disconnects provide three 30 amp poles to remove all power safely from Bebco Wall Mount Air Conditioner and Heat Pump Units. These switches are intended and suitable for mounting on or near the exterior surface of the unit to safely disconnect power from these devices, and they include a separate label to properly identify their purpose, which can be easily attached to any dry, clean surface.

Model EDS

Explosion-Proof Power Disconnect Switch
Provides power disconnect for Bebco Wall Mount
Air Conditioners and Heat Pumps!

* Contact Rating: 30 Amps, Maximum
*Circuit Wiring: 3-Pole, Non-Fused
* Body Material: Cast Aluminum
* Cover Material: Thermoplastic
*Operator Paddle: Phenolic Toggle
*Overall Height: 6.36 Inches
*Overall Width: 3.95 Inches
*Overall Depth: 4.35 Inches
*Switch Action: Maintained Position
*Voltage Rating: 600VAC/230VDC, Maximum
* Circuit Rating: 5000 Amp Short Circuit Rating
*Terminal Type: Screw Clamp Terminals
*Lockout Method: Padlock Shackle Hole
*Mounting Style: 2-Point Surface Mount
* Conduit Ports: Top and Bottom, 3/4" Female Thread
* Certifications: UL Listed, CSA Certified, CE Marked

Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!

Condenser Air Filters

Bebco provides these filters as spare parts for Bebco Wall Mount Air Conditioner & Heat Pump Units to filter outdoor air as it enters the condenser compartment, to overcome extreme dust conditions and keep the condenser coil clean.

Model CAF Filters are washable, and can be replace easily while your Bebco Model WAC or WHP Unit continues to operate, which ensures years of trouble free service while minimizing the need to clean your unit’s coils.

Bebco provides this accessory to facilitate proper unit maintenance and operation!

Model CAF

Bebco Model CAF Condenser Air Filters are stainless steel, 250 micron, reusable air filters available in Standard or High Capacity efficiency ratings. They are strongly recommended for any Wall Mount Air Conditioner or Heat Pump located in mild to extremely dusty or outdoor environments, to maintain proper filtration of air passing over Bebco Unit condenser coils at all times.

Consider Model CAF Condenser Air Filters as an ideal aspect of a strong and active preventive maintenance program, and contact a Bebco Sales Associate for more information now!

Model CAF

Condenser Air Filters
Provides positive filtration of the condenser compartment
in mild to extremely dusty environments!

*Construction: Riveted Channel Frame w/ Woven Mesh
*Frame Material: .024” 304 Stainless Steel
* Filter Mesh: .032 Strand 304 Stainless Steel
* Mesh Density: 250 Micron
* Arrestance: 40-65% or 65-80% effective
on >10.0 pm Particles

IMPORTANT NOTES:

  1. Unit Serial Numbers may be requested to acquire these filters if not ordered simultaneously with Units, to ensure proper fit.
  2. Filter sizes vary for all Bebco Model WAC & WHP Units.
  3. Consult a Bebco Salesperson or examine your unit to determine your needs.

Ask a Bebco Sales Associate about our retrofit condenser air filter kits to
add this essential accessory to your unit now!

Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!

Return Air Filters

Bebco provides these filters as spare parts for Bebco Wall Mount Air Conditioner & Heat Pump Units to filter recirculated room
air as it returns to the Unit, in order to keep room air fresh and the evaporator coil clean.

Model RAF Filters can replace dirty in-service filters quickly, while your Bebco Model WAC or WHP Unit continues to operate, which
ensures years of trouble free service while minimizing the need to clean your unit’s coils.

Bebco provides this accessory to facilitate proper unit maintenance and operation!

Model RAF

Bebco Model RAF Return Air Filters are designed to consistently increase efficiency throughout their life cycle and have a MERV 8 rating. Among chief benefits, the media weaving process is carefully controlled and an antimicrobial coating is applied to support optimal indoor air quality. Our filters are also mechanically efficient, self-supporting and do not rely upon metal wire.

Best of all, they present low initial resistance, are environmentally friendly, incorporating no dies or metal, and they are completely safe for landfill disposal or incineration. Consider this important accessory as a way to ensure your unit performs at optimal levels at all times, while maintaining a clean, healthy and safe work environment!

Model RAF

Return Air Filters
Provides positive filtration of return air while keeping
room air fresh and evaporator coils clean and efficient!

* Construction: Commercial Adhesive Bonding
* Frame Material: Die-Cut 28 Pt. Beverage Board
* Filter Media: Self-Supporting Pleated DuraFlex®
with Antimicrobial Properties
*Initial Resistance: .23" to .38" w.g. (inches of water)
* MERV Rating: 8 (per ASHRAE 52.2)
* Media (filter) Thickness: 1, 2 or 4 Inches (see notes below)
* Disposal: Environmentally Safe - No Dies,
No Metal & Fully Incinerable

IMPORTANT NOTES:

  1. Unit Serial Numbers may be requested to acquire these filters if not ordered simultaneously with Units, to ensure proper fit.
  2. Filter size and thickness vary for all Bebco Model WAC & WHP Units.
    Consult a Bebco Salesperson or examine your unit to determine your needs.
  3. Ask a Bebco Sales Associate about our replacement filter program
    to ensure essential routine service and keep room air fresh!

Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!