Marine Grade Wall & Remote Mount NFPA 496 Building Pressurization Units

Unit Accessories

The accessories listed below enhance operation, support maintenance and provide local alarms to summon attention to performance issues or the presence of flammable or corrosive gases!

Click any Accessory Technical Bulletin button to learn more about our complete line of accessories!

A wide range of accessories easily enhance our through-wall Air Conditioners & Heat Pumps to meet your precise application needs!

Click any item to enlarge…

Bebco provides these assemblies to serve as a fresh air intake for our Whisper Drive™ Pressurization Units. Spiral Pipe Stacks are an essential accessory that provide an economical and guy-wire secured source of fresh air.

When properly secured, these stacks are designed to withstand extremely high wind-loads, are certified for coastal areas, and they are provided with a very wide range of accessories including fittings, flexible duct connectors, anchor kits and rain caps.

Bebco provides all necessary accessories to complete your installation easily!

Bebco Whisper Drive™ Pressurization Unit Spiral Pipe Stacks Assemblies

Model SP Spiral Pipe Stacks, along with Model SN Ninety and Model ST Tee Stack Fittings and Model SC Stack Caps provide an economical and easily installed fresh air intake system for Bebco Building Pressurization Units. The Model SP Spiral Pipe Stacks are available in standard lengths of 10 or 14 feet and in custom lengths, with 12”, 16”, 20”, and 24” diameters in either galvanized or stainless-steel materials with optional finishes.

Model CAGK and EAGK Concrete Anchor and Earth Auger Kits provide complete guy wire support systems, including ground level anchors, spiral pipe guy wire attachment brackets, turnbuckles and guy wire cable. As an alternative, Bebco also offers a unique telescoping Model SPSK Spiral Pipe Stanchion Kit to eliminate some or all guy wire supports. Finally, to facilitate easy connection to a Bebco Whisper Drive™ Pressurization Unit, and eliminate alignment and stress issues, Bebco recommends the use of Model FDC Flexible Duct Connectors. Contact a Bebco Sales Associate to discuss your application and review this product line’s technical bulletin for more information!

SPSA Series

Spiral Pipe Stack Assemblies
Provides an economical fresh air intake system for
Bebco Whisper Drive™ Building Pressurization Units.

SP, SC, ST & SN

Spiral Pipe, Caps, Tees & Nineties

Materials:

16 or 20 Gauge Bodies & 1/4" or 3/16"

Flanges in Galvanized, 304 Stainless

Steel or 316 Stainless Steel Material

Finishes:

Unfinished, Hot Dipped, or

Urethane Painted

Stack Diameters:

8", 10", 12”, 16”, 18", 20” or 24”

Accessories

Model BC

Blind Covers

Model FDC

Flexible Duct Connectors

Model GBK

Gasket & Bolt Kits

Model SPAK

Spiral Pipe Anchor Kits

Model CAGK

Concrete Anchor Guy Wire Kit

Model EAGK

Earth Auger Guy Wire Kit

Model SPSK

Spiral Pipe Stanchion Kit

Open this Series’ Technical Bulletin in a separate window!

Technical Bulletin

Bebco Whisper Drive™ Pressurization Unit Spiral Pipe Stacks

This multi-story building features a 20” diameter Bebco Spiral Pipe Stack feeding a Bebco Dual Channel Gas Phase Filtration and Pressurization Unit. In turn, it feeds two Bebco Model WAC Wall Mount Building Air Conditioners. The Spiral Pipe Stack is attached to the structure’s wall at two points to provide adequate support and extends slightly above the third level of this massive structure.

Model WDP & RDP Whisper Drive™ Building Pressurization Unit fresh air intake ports can also be served by SPSA Series Spiral Pipe Stack Assemblies, which come complete with all essential components to complete your installation, including fittings, guy wire kits, anchor bolts and stanchion supports. Contact a Bebco Sales Associate to discuss your application and review this product line’s extensively detailed technical bulletin for a complete overview of all features and options!

Bebco Spiral Pipe Stacks provide an economical and extremely versatile fresh air intake assemblies for applications where guy wires or other supports are acceptable!

Bebco provides these assemblies to serve as a fresh air intake for our Whisper Drive™ Pressurization Units, to provide a free-standing fresh air intake stack, when spiral pipe is not plausible, acceptable or preferred.

These stacks are designed to withstand extremely high wind-loads, are certified for coastal areas, and they are provided with a range of accessories including flexible duct connectors, anchor kits and rain caps.

Bebco provides all necessary accessories to complete your installation easily!

Bebco Whisper Drive™ Pressurization Unit Rigid Pipe Stacks Assemblies

Model RP Rigid Pipe Stacks, Model RPAK Rigid Pipe Anchor Bolt Kits, and Model SC Stack Caps provide a fresh air intake system for Bebco Building Pressurization Units. The Model RP Rigid Pipe Stacks are available in 12”, 16”, 20”, and 24” diameters in either carbon steel or stainless steel. Model RP Rigid Pipe Stacks are 25 feet tall single piece stacks constructed from seal-welded 1/4” thick (schedule 20) carbon or stainless-steel pipe.

The Model RP feature a seal-welded flange at the top for the stack cap connection and a seal-welded blind flange at the bottom for mounting to a concrete slab. To facilitate easy connection to a Bebco Whisper Drive™ Pressurization Unit, and eliminate alignment and stress issues, Bebco recommends the use of Model FDC Flexible Duct Connectors. Contact a Bebco Sales Associate and review this product line’s technical bulletin for more information!

RPSA Series

Rigid Pipe Stack Assemblies
Provides a free standing fresh air intake system for
Bebco Whisper Drive™ Building Pressurization Units.

Model RP

Rigid Pipe Stack

Materials:

Schedule 20 150# Rated Carbon Steel,

304 Stainless Steel or 316 Stainless Steel

Finishes:

Carbon Steel: Hot Dip Galvanized

Stainless Steel: 2B or Urethane Painted

Stack Diameters:

8", 10", 12”, 16”, 18", 20” or 24”

Model SC

AFlex Duct Connectors

Duct Material:

Polyester/Neoprene w/ Galvanized Helix

Flange Material:

16 Gauge Galvanized Steel,

304 Stainless Steel or 316 Stainless Steel

Model RPAK

Rigid Pipe Anchor Kits

Materials:

Zinc Chromate Plated Carbon Steel.

304 Stainless Steel or 316 Stainless Steel

Styles:

Concrete Epoxy or Wedge Anchors

or Platform Deck Bolts

Open this Series’ Technical Bulletin in a separate window!

Technical Bulletin

LBebco Whisper Drive™ Pressurization Unit Rigid Pipe Stacks

In an extremely unique application, this Emergency Deluge Fire Pump Engine Building is equipped with an oversized Bebco Model WDP Wall Mount Whisper Drive™ Building Pressurization Unit. As shown, the Unit is fed by a free-standing Bebco Model RPSK Rigid Pipe Stack, constructed from Schedule 20 carbon steel pipe and mounted to a detachable entryway platform, next to the front door.

The WDP Unit pressurizes the building and also provides emergency ventilation if interior gas detection units sense engine fuel or exhaust gases within the building. As shown in the inset image, the engine has a ducted exhaust, but relies on the automatic controls of the Whisper Drive™ Unit to supply its massive amount of intake air, while the WDP Unit also accomplishes pressurization and achieves the required 60 feet per minute air velocity through both doors when fully opened!

In this instance, the unique free-standing attributes of the Bebco Rigid Pipe Stack permitted this new building to be located within a densely occupied area of a refinery, without the need for the extensive space and clearances required for guy wire supports!

Bebco Rigid Pipe Stacks provide a free-standing fresh air intake for applications where guy wires are either impractical
or cannot be accommodated!

The Model FID Flexible Intake Duct provides a temporary, pliable fresh air duct connection to Bebco Model WDP or RDP Unit. Model FID is typically utilized in applications where the use of a permanent spiral or rigid pipe stack is not feasible.

When placed properly, the intake housing draws unclassified, fresh air into a Bebco Whisper Drive™ Pressurization Unit
from an unclassified area adjacent to the immediate vicinity.

Bebco provides all necessary accessories to complete your installation easily!

Bebco Whisper Drive™ Building Pressurization Unit Flexible Intake Duct

Bebco Model FID Flexible Intake Duct housings are manufactured from 304 and 316 stainless steel components, and the duct features a pliable neoprene coated polyester hose with a mechanically embedded galvanized steel helix to withstand years of exposure to harsh operating conditions and corrosive environments.

They serve to provide a source of fresh air where the use of a permanent spiral or rigid pipe stack is not feasible, and they are provided with 25 feet or custom length duct. Contact a Bebco Sales Associate for more information about custom duct lengths and housing options.

Model FID

Flexible Intake Ducts
Provides a temporary, pliable fresh air duct connection to Bebco Wall
Mount or Remote Mount Pressurization or Ventilation Units.

Housing Material:

14 Gauge 304 Stainless Steel

Housing Finish

Unfinished, Urethane Paint or Custom Finish

Housing Handle:

316 Stainless Steel

Housing Screen:

.047” Wire Diameter x 0.25” Opening

Woven 316 Stainless Steel Mesh

Duct Material:

Neoprene Coated Polyester Fabric

w/ Embedded Galvanized Helix

Duct Clamps:

304 Stainless Steel

Duct Diameters:

12”, 16”, 20”, or 24”

Duct Lengths:

25 Feet or Custom Length *

* Ask A Bebco Sales Associate about custom lengths and options!
Open this Series’ Technical Bulletin in a separate window!

Technical Bullitin

Bebco Whisper Drive™ Pressurization Unit
Flexible Intake Duct Applications next

Bebco Model FID Flexible Intake Ducts are typically used in both off-shore and on-shore applications to provide fresh air to portable mud or data logging stations, laboratories, wire-line control cabins and other temporary or mobile workstations.

Often, the closest source of fresh air is either to one side or the other of such portable units or sometimes below deck! Regardless of where fresh air can be obtained, a flexible intake duct provides a fast and easy means to get portable workstations up and running quickly, when downtime is not an option and seconds count!

Bebco Flexible Intake Ducts provide a fast and sure way to obtain fresh air when time is of the essence!

Bebco provides these accessories to provide an aesthetic connection of the discharge of Bebco Remote Mount Whisper Drive™ Pressurization Units to your building’s wall or roof cutout or the fresh air intake of an HVAC unit.

These accessories are provided with concealed clamps that join them together and to the pressurization unit, maintaining a clean, sleek look, eliminating the need for less ergonomic ductwork fabrication by others.

Bebco provides all necessary accessories to complete your installation easily!

Bebco Remote Mount Whisper Drive™ Pressurization Unit
Remote Mount Discharge Accessories

Model ADGA, DE, DN & DCF

Discharge Grill, Extensions, Nineties & Curb Flanges
Provides a leak-proof, aesthetic ductwork connection between a Remote
Mount Pressurization Unit and a protected building’s wall, roof or AC unit.

Body Materials:

Galvannealed Steel, 304 Stainless Steel

or 316 Stainless Steel

Material Finishes:

2B Finish or Urethane Paint

Gasket Material:

One-Piece Replaceable Neoprene

Concealed Clamps:

Galvanized Steel

Sizes:

12", 16", 20" & 24"

Concealed Clamps are supplied to join all parts
quickly and ergonomically!

Bebco RMDA Remote Mount Discharge Accessories provide the perfect solution for connecting your remote mount unit to a wall cutout, roof cutout or fresh air intake of an HVAC Unit as illustrated above. The Adjustable Discharge Grill accommodates wall or roof penetrations ranging from 4” to 8” deep, and Discharge Extensions are available in standard or custom lengths as needed to meet your specific application requirements.

As shown, these accessories are seal-welded, maintain the sleek and clean appearance of the unit, and are easily joined to your remote mount unit and to each other with concealed compression clamps. These accessories make installation of a remote mount unit fast and easy, and allow you to pressurize a building effortlessly and in complete compliance with NFPA 496. Contact a Bebco Sales Associate and review this product line’s technical bulletin for more information, and ask us about customization as required to fit your unique application needs!

Bebco provides these accessories to achieve the ultimate level of safety when Bebco Whisper Drive™ Pressurization Units are fitted on buildings containing analyzers or other processing equipment that requires hydrocarbon gas, H2S gas or O2 deficiency monitoring.

These systems can be integrated easily and come with all necessary components to detect critical hazards and warn your facility’s safety personnel of potentially catastrophic conditions.

Bebco provides all necessary accessories to complete your installation easily!

Hazardous Location Whisper Drive™ Pressurization Unit
Gas Detection Systems

Bebco GDS Series Gas Detection Systems are intended to alert your team to unacceptable levels of flammable, combustible or toxic gases, or to monitor oxygen levels within a building or room containing analyzers or other chemical processing equipment. The power supply requires a 120 VAC power source and feeds 24 VDC to the monitor, which powers the sensor within the protected enclosure. The monitor then sends a 4-20 ma signal to an alarm monitoring system to alert your staff of critical conditions.

Bebco also offers a unique and easily installed Model GDSB Gas Detector Sensor Bracket for your fresh air intake stack, that includes a gasketed and contoured stainless steel seal-welded sensor housing, rated conduit fittings for the installation of a gas sensor and an integrated gas tubing port to simplify calibration tasks and ensure proper sensor maintenance. When it comes to ensuring your team’s safety, Bebco has a total solution and the expertise to help you get it properly installed!

Model CGDM, HGDM, OGDM, GDPS & GDSB

Monitors, Matching Sensors & Power Supplies
Provides detection of hydrocarbons, H2S or O2 deficiency!

Hydrocarbon Monitor:

Catalytic Bead Adsorption - 0-100% LEL

Accuracy & Repeatability: +/- 5% Full Scale

Zero Drift: < 5% per Year

H2S Monitor:

Metal Oxide Adsorption - 0-100 PPM

Accuracy & Repeatability: +/- 5% Full Scale

Zero Drift: < 2% per Year

O2 Monitor:

Electrochemical Fuel Cell - 0-26%

Accuracy & Repeatability: +/- 2% Full Scale

Zero Drift: < 2% per Month

Response/ Op Temp:

90% < 30 Seconds / -40° to 175° F

Housing Ratings:

NEMA 7, Class 1, Division 1, Group C & D

Housing Dimensions:

5.5" H x 5.3" W x 4.0" D (GDPS is 6.0" D)

Power Requirements:

Monitor: 22-28 VDC / Power Supply: 120 VAC

Signal Output:

4-20ma VDC, Linear

Alarm Contacts:

Low & High Set Points & Fault Supervision

Form C 0.5 amps @ 125 VAC or 30 VDC

Programmed to open or close on alarm

Conduit Ports:

3/4" Top & Bottom Sides

Certification:

UL Listed

Open this Series’ Technical Bulletin in a separate window!

Technical Bulletin

Model BPCN Building Pressurization Caution Nameplates are intended to label all routinely used personnel access doors of a building protected with a Bebco Whisper Drive™ Building Pressurization Unit.

Model SDWN Building Pressurization Warning Nameplates are intended to label all infrequently used (sealed) equipment access doors of a building protected with a Bebco Whisper Drive™ Building Pressurization Unit.

Bebco provides these accessories to ensure full compliance to NFPA 496 Requirements!

NFPA Compliant Caution & Warning Nameplatess

Bebco Model BPCN Nameplates are required for all personnel doors, and caution that the building is pressurized and the door must be firmly secured after entering or exiting. The nameplate also warns against leaving the door open unless the area is known to be free of flammable materials or unless all unprotected devices have been de-energized.

Model SDWN Nameplates are required for all equipment doors and warn against opening the door without permission of the operational management authority except in the event of a life-threatening emergency, unless the surrounding area is known to be free of flammable materials or unless all unprotected devices have been de-energized. Contact a Bebco Sales Associate for more information, and consider our various sizes depending on your particular conditions.

Model BPCN & SDWN

Caution & Warning Nameplates
Provides code compliant and critical cautions and warningson all personnel and equipment doors!

Material:

Reverse Silkscreened Lexan®

Adhesive Backing:

* 3M® VHB®

Mounting Hole Diameter:

0.125”

Dimensions:

BPCN-1 & SDWN-1: 6” W x 4” H

BPCN-2 & SDWN-2: 12” W x 8” H

BPCN-3 & SDWN-3: 16” W x 10.5” H

* Door surfaces must be cleaned for maximum adhesion.
Lexan® is a registered trademark of the General Electric Corporation 3M® & VHB® are trademarks of the 3M Corporation
Open this Accessory’s Technical Bulletin in a separate window!

Technical Bulletin

Bebco RECO Series Remote Emergency Control Operators are intended to activate or deactivate the emergency shutdown (ESD) and emergency control over-ride (ECO) functions of Bebco Whisper Drive™ Building Pressurization Units.

They are designed to work in conjunction with hard-wired or intrinsically safe inputs to these units, and they can operate independently or in conjunction with other safety devices such as our Model CGDM Combustible Gas Detection Monitor.

Bebco provides these accessories to provide remote control inputs to your pressurization unit!

Whisper Drive™ Unit Remote Emergency Control Operators

Bebco RECO Series Remote Emergency Control Operators meet the most demanding needs for strength, along with corrosion, chemical and UV resistance. RECO Series Enclosures are formed as molded polyester housings and covers with a recessed high temperature neoprene gasket and captive stainless steel screws. The enclosures are watertight, dust tight, double insulated and non-conductive, making them ideal for any location, even when subjected to frequent wash-downs.

RECO Series Operators are also incredibly durable, with highly corrosion and chemical resistant bodies and internal metal operator components to provide the perfect combination of durability and strength essential to industrial applications. Contact a Bebco Sales Associate and review this product line’s technical bulletin for more information.

RECO Series

Remote Emergency Control Operators
Provides remote control of emergency shutdown
and over-ride functions!

Housing Material:

Fiberglass Reinforced Polyester

Cover Gasket Material:

Memory Retaining Polyurethane

Enclosure Dimensions:

6-5/8” H x 3-13/16” W x 3-57/64” D

Conduit Connection:

One (1) 3/4" Bottom Side Conduit Knockout

Certifications:

UL & CSA Listed as Type 1, 3, 4X, 6P & 12

Temperature Range:

-40 to +250° F (-40 to +120° C)

Flammability Rating:

UL94-5V, Self-extinguishing,
non-flame propagating

Conductivity Rating:

Non-conductive, Double Insulated

Environmental Rating:

UV and Chemical Resistant

Operator & Contact
Blocks:

Thermoplastic Polyester

Ordinary Block
Certifications:

UL & CSA Listed for Industrial Use

Hazardous Block
Certifications:

UL & CSA Listed for Class I, Division 2,

Groups B, C & D

Open this Accessory’s Technical Bulletin in a separate window!

Technical Bulletin

Bebco provides these accessories for Bebco Whisper Drive™ Pressurization Units to indicate that building or room pressure is below the alarm set point. In tandem, the VFDI Card permits you to set an alarm pressure and an alarm delay to prevent nuisance alarms.

These alarm devices can be mounted on or near the protected building or room, are rated for the Hazardous Location and are also perfect companions to our Gas Detection Systems, to provide alarms for combustible or corrosive gases and oxygen deficiency.

Bebco provides all necessary accessories to complete your installation easily!

Hazardous Location Enclosure Air Conditioner
Remote Alarm Beacons & Horns

Available for Class I, Division 1 or Class I, Division 2 applications, Bebco Model RAB-1, RAB-2 and ERAB-2 Remote Alarm Beacons and Model RAH-1 and RAH-2 Remote Alarm Horns are intended to provide audible or visual signals that summon Operators to resolve loss of building or room pressure, when used in conjunction with Model WDP or RDP Pressure Loss Alarm Contacts. These alarm devices can also be used in conjunction with our Gas Detection Systems to address the presence of combustible or corrosive gases or investigate oxygen deficiencies, or with both sets of contacts for a common trouble alarm, if wired in series.

All devices are listed for use in Class I, Division 1 or 2 Hazardous Locations and are considered as highly suitable alarm devices by most industry standards. Contact a Bebco Sales Associate or review this product line’s technical bulletin for more information.

Hazardous Location Enclosure Air Conditioner
Remote Alarm Beacons & Horns next

This Fiberglass Analyzer Building is situated in an H2S environment of a sour gas plant, and is equipped with Bebco Whisper Drive™ Pressurization Unit Remote Alarm Beacons & Horns to indicate loss of pressure and fresh air intake contamination. By providing suitable local alarms, operators are alerted instantly to critical conditions to ensure this analyzer building and the equipment it contains perform flawlessly in extremely corrosive and volatile conditions!

Bebco Remote Alarm Beacons & Horns provide visual and audible signals that summon operators to critical fault conditions!

Area Classification Ratings for each device vary…

Please see our Technical Bulletin for complete information or contact a Bebco Sales Associate for assistance!

 

Model ERAB, RAB & RAH

Remote Flashing Alarm Beacons & Audible Tone Horns
Provide visual and audible signals to summon Operators to fault conditions

ERAB-2Economy Remote Alarm Beacon
Materials:Aluminum Housing w/ Polyurethane Finish

& Polycarbonate Outer Dome
Mounting:Pendant w/ 3/4" Conduit
Dimensions:7.5” H x 5.5” Diameter
Shipping Weight:2 Pounds
Operating Temp:-40° F - 104° F
Operating Voltage:12-24 VDC @ 1.70-0.70 Amps

24 VDC @ 0.70 Amps

120 VAC @ 0.21 Amps

240 VAC @ 0.13 Amps
Flash Rate:80 / Minute
Certifications:Class I, Div 2 - UL Listed, CSA Certified
RAB-2Flashing Remote Alarm Beacon
Materials:Cast Aluminum Body with Epoxy Finish

& Glass Dome w/ Optional Guard
Mounting:Pendant or Ceiling w/ 3/4" Conduit
Dimensions:9.25” H x 5.5” Diameter
Shipping Weight5 Pounds
Operating Temp:-31° F - 104° F
Operating Voltage:24 VDC @ 0.4 Amps

120-240 VAC @ 0.21-0.13 Amps

277 VAC @ 0.13 Amps
Flash Rate:60 / Minute or Steady Burn
Certifications:Class I, Div 2 - UL Listed, CSA Certified
RAH-2Continuous Tone Remote Alarm Horn
Material:Die Cast Zinc w/ Polyurethane Finish
Mounting:Surface w/ 3/4" Conduit
Dimensions:4.53” H x 6.02” W x 3.66” D
Shipping Weight:3 Pounds
Operating Temp:-65° F - 150° F
Maximum Sound:100 Decibels at 10 ft.
Operating Voltage:120VAC 50/60Hz @ 0.18 amps

240VAC 50/60Hz @ 0.09 amps
Certifications:Class I, Div 2 - UL Listed, CSA Certified
RAB-1Div 1 Flashing Remote Alarm Beacon
Materials:Cast Aluminum Body with Epoxy Finish

& Glass Dome w/ Optional Guard
Mounting:Pendant, Wall or Ceiling Mount w/ 3/4 Conduit
Dimensions:14.26" - 15.48" H x 8.80” Diameter
Shipping Weight:15.9 -19.8 Pounds
Operating Temp:-67° F - 150° F
Operating Voltage:24 VDC @ 1.9 Amps

120 VAC 50/60 Hz @ 1.14 Amps

240 VAC 50/60 Hz @ 1.14 Amps
Flash Rate:80 / minute
Certifications:Class I, Div 1 - UL Listed, CSA Certified
RAH-1Div 1 Continuous Tone Remote Alarm Horn
Material:Cast Aluminum Body
Mounting:Pendant or Surface w/ 3/4" Conduit
Dimensions:7.625” H x 6.875” D x 6.5” D
Shipping Weight:2 Pounds
Operating Temp:-13° F - 104° F
Maximum Sound:100 Decibels at 10 ft. (5 minute duty cycle)
Operating Voltage:24 VDC @ 1.2 Amps

120 VAC 50/60 Hz @ 0.20 Amps

240 VAC 50/60 Hz @ 0.10 Amps
Certifications:Class I, Div 1 - UL Listed, CSA Certified

Open this Accessory’s Technical Bulletin in a separate window!

Technical Bulletin

Bebco provides these filters as spare parts for Units that draw air from mild to extremely dusty environments to ensure positive filtration and that wasps, bees, moths, mosquitoes or any other insects are not introduced into your pressurized room or building.

Model DAF Filters can be exchanged quickly with dirty in-service filters, allowing your Bebco Whisper Drive™ Pressurization Unit to continue operating efficiently while dirty filters are properly washed and prepared for reuse.

Bebco provides this accessory to facilitate proper unit maintenance and operation!

Whisper Drive™ Unit Discharge Air Filters

Bebco Model DAF Discharge Air Filters are stainless steel, 250 micron, reusable air filters for Bebco Model WDP & RDP Pressurization Units and WVF & RVF Ventilation Fans. They are strongly recommended as spare parts for Units that draw air from mild to extremely dusty environments to ensure positive filtration of air entering a room or building at all times. In addition, they serve to ensure that wasps, bees, moths, mosquitoes or any other insects are not introduced into a pressurized or ventilated space.

Model DAF

Discharge Air Filters
Provides positive filtration of inlet air while prohibiting
the introduction of insects into a pressurized space!

Construction:

Riveted Channel Frame w/ Woven Mesh

Frame Material:

.024” 304 Stainless Steel

Filter Mesh:

.032 Strand 304 Stainless Steel

Mesh Density:

250 Micron

Arrestance:

65-80% efficiency on >10.0 pm Particles

IMPORTANT NOTES:

  1. Unit Serial Numbers may be requested to acquire these filters if not ordered simultaneously with Units, to ensure proper fit.
  2. Model RDP Remote Mount Pressurization Units require Model ADGA Adjustable Discharge Grille Assemblies or Model IDFH In-Line Discharge Filter Housing to accommodate these filters.
  3. Ask a Bebco Sales Associate about retrofit kits to modify your existing Bebco Units to accept this important accessory

Open this Accessory’s Technical Bulletin in a separate window!

Technical Bulletin

Bebco provides this accessory to serve as a disconnect for Bebco Whisper Drive™ Building Pressurization Units, which
may be required depending on how the unit is powered.

These disconnects can be mounted on or near the unit, are rated for the hazardous Location and are a perfect solution for proper power control.

Bebco provides all necessary accessories to complete your installation easily!!

Bebco Whisper Drive™ Building Pressurization
Units Power Disconnects

Bebco Model EDS Explosion-Proof Disconnects provide three 30 amp poles to remove all power safely from Bebco Whisper Drive™ Building Pressurization Units. These switches are intended and suitable for mounting on or near the exterior surface of the unit to safely disconnect power from these devices, and they include a separate label to properly identify their purpose, which can be easily attached to any dry, clean surface.

Model EDS

Explosion-Proof Power Disconnect Switch
Provides power disconnect for Whisper Drive™
Building Pressurization Units!

Contact Rating:

30 Amps, Maximum

Circuit Wiring:

3-Pole, Non-Fused

Body Material:

Cast Aluminum

Cover Material:

Thermoplastic

Operator Paddle:

Phenolic Toggle

Overall Height:

6.36 Inches

Overall Width:

3.95 Inches

Overall Depth:

4.35 Inches

Switch Action:

Maintained Position

Voltage Rating:

600VAC/230VDC, Maximum

Circuit Rating:

5000 Amp Short Circuit Rating

Terminal Type:

Screw Clamp Terminals

Lockout Method:

Padlock Shackle Hole

Mounting Style:

2-Point Surface Mount

Conduit Ports:

Top and Bottom, 3/4" Female Thread

Certifications:

UL Listed, CSA Certified, CE Marked

Open this Accessory’s Technical Bulletin in a separate window!

Technical Bulletin